Search Results

The outline of the TOYOTA FCHV-adv is described in this paper. The TOYOTA FCHVadv achieved an approximately 25 percent improvement in vehicle fuel efficiency and about 1.9 times the amount of usable hydrogen in comparison with the previous model. These improvements have enabled almost 2.5 times longer practical cruising range, more than 500 km. The freeze start capabilities of the FCHV-adv were improved by modifying the FC stack and control system. As a result, the FCHV-adv has been capable of starting at a temperature of -30°C. In the future, TOYOTA intends to improve durability and reduce costs.

In order to reduce CO2, EV and Hybrid Vehicle (HV) are effective. Those type vehicles have different power train from conventional vehicle. Those new power trains drastically improve their efficiency from conventional vehicle with keeping same or superior power performance. On the other hand, those vehicles have the issue for thermal energy shortage during warming up process. The thermal energy is very large. The thermal energy seriously affect on the fuel economy for HV and the mileage for EV. In this paper, the power performance, the fuel economy and the effect of heat energy recovery from the exhaust gas are discussed for HV. For the power performance, the simulated acceleration time of 0-100km/h was 11.8sec and the measured vehicle time was 11.9sec. The error between simulation and actual measurement result was 1.2%. As for the fuel economy, the energy management using exhaust gas heat exchange system improved 10.3% of the fuel consumption during warming up.

Turbocharged downsized gasoline engines have been widely used in the market as one of the measures to improve fuel economy. Coking phenomena in the lubricating circuit of the turbocharger unit is a well-known issue that may affect turbocharger efficiency and durability. Laboratory rig test such as ASTM D6335 (TEOST 33C) has been used to predict this phenomenon as a part of engine oil performance requirements. On the other hand, laboratory tests sometimes have difficulty reproducing the actual mechanism of coking caused by engine oil degradation. Accumulation of insoluble material is one of the important gasoline engine oil degradation modes. The influence of temperature and insoluble concentration were investigated based on actual used engine oils collected in the field.

In recent years, from a viewpoint of global warming and energy issues, the need to improve vehicle fuel economy to reduce CO2 emission has become apparent. One of the ways to improve this is to enhance engine thermal efficiency, and for that, automakers have been developing the technologies of high compression ratio and dilute combustion such as exhaust gas recirculation (EGR), and lean combustion. Since excessive dilute combustion causes the failure of flame propagation, combustion promotion by intensifying in-cylinder turbulence has been indispensable. However, instability of flame kernel formation by gas flow fluctuation between combustion cycles is becoming an issue. Therefore, achieving stable flame kernel formation and propagation under a high dilute condition is important technology.

Recently, the plastic material is positively introducing for automotive parts due to the Needs of vehicle weight reduction and cost saving. On the other hand, the countermeasure for scrapped car is a big subject to need to consider as a car maker. Therefore, the development of recycling technology for plastic parts has been necessary. In this study, we tried to develop recycling technology for glass fiber reinforced Polyamide6(PA6) which is applied to various automotive parts like an air intake manifold. As a recycling technique, we focused on the chemical recycling which can reclaim raw material of PA6(ε- caprolactams) from the post-consumer automotive parts. The chemical recycling we selected can be put on a higher priority because it has possibility to utilize the limited resource repeatedly. As a result, we could retain high purity of ε- caprolactams using our following two techniques which make possible to recycle Polyamide 6 materials. One is to separate PA6 from glass fiber.

Toyota has developed and confirmed the efficiency of a hybrid system using a continuously variable transmission (CVT) for relatively large vehicles like minivans. The fuel economy is double that of vans of the same class (in the Japan 10-15 test mode), and the system meets the emissions requirements for the U-LEV category. The hybrid system is configured for four-wheel drive. The front drive unit has a gasoline engine and an electric motor that are connected to a power-switching device, the output from which is conveyed to the CVT. The rear drive unit has an electric motor and a reduction gear that are independent of the front unit.

In order to reduce tail-pipe hydrocarbon emissions from SI gasoline engines, rapid catalyst warm-up and improvement of catalyst conversion efficiency are important. There are many reports which have been published by manufacturers and research institutes on this issue. For further reduction of tail-pipe hydrocarbon emissions, it is necessary to reduce engine-out hydrocarbon emissions and to improve after treatment, during the time the catalyst is not activated. This paper quantitatively analyzed the fuel amount of intake port and cylinder wall-wetting, burned fuel and engine-out hydrocarbon emissions, cycle by cycle in firing condition, utilizing a specially designed analytical engine. The effect of mixture preparation and fuel properties for engine-out hydrocarbon emissions, during the cold engine start and warm-up period, were quantitatively clarified.

Multi-cylinder hydrogen-absorbing alloy tanks for fuel cell vehicles have 10 to 40 metallic cylinders that are bundled and filled with hydrogen-absorbing alloy. In this system, the cylinders themselves act as a heat exchanger and the working pressure is lowered to 10 to 20 MPa compared with high-pressure MH tanks. Moreover, both heat conduction and mass reduction can be achieved by reducing the wall thickness of the cylinders. A model verification experiment was conducted using a one-quarter-scale prototype of a full size tank, and a conduction simulation model verified in the experiment was used to predict the performance of the full size tank. Results showed that it is possible to fill the tank with hydrogen to 80% of its capacity in a five-minute filling time, although issues related to heat conductivity performance require improvement. Accordingly, it may be possible to adopt this tank as part of a system if the storage amount of the hydrogen-absorbing alloy can be increased.

Aisin AW (AW) and Toyota Motor Corporation (TMC) have developed a new rear wheel drive (RWD) 10-speed automatic transmission, AWR10L65 (TMC name: AGA0), suitable for RWD/AWD luxury passenger cars and sports cars. This 10-speed automatic transmission provides enhanced drivability leading to outstanding driver satisfaction. This has been accomplished using a close ratio gear train with optimized gear steps for rhythmic shift changes and quick acceleration. Low rpm lock-up and highly responsive shift changes result in a direct shift feel. This automatic transmission contributes to improved fuel economy by having higher efficiency and lower mass than current 8-speed RWD automatic transmissions.

A new hybrid transmission has been developed for New compact class vehicles. The development of this transmission has been aimed at improving fuel economy and achieving the weight reduction and compact size. In order to achieve these goals, the gear train and motor have been newly designed and advanced technology applied. This paper describes the major features and performance of this transmission in detail.

A study was conducted to reduce unburned oil fractions in diesel particulate matter (PM) by improving oil consumption. A method utilizing radioisotope 14C was developed to measure the unburned oil fractions separately for the four paths by which oil is consumed: valve stem seals, piston rings, PCV system, turbocharger. The conversion ratio of oil consumption to PM was calculated by comparing the unburned oil emission rates with oil consumption rates, which were obtained by the use of the 35S tracer method. The result in an experimental diesel engine shows the highest conversion ratio for the oil leaking through the valve stem seals. The modifications to the engine were thereby focused on reducing the leakage of the stem seals. This stem seal modification, along with piston ring improvements, reduced oil consumption, resulting in the unburned oil fractions in PM being effectively reduced.

Toyota Motor Corporation has recently developed a new six-speed automatic transmission (A761E) for Front Engine Rear Wheel Drive (FR) vehicles. Following the general trend of increased shift stages and a wider range of gear ratios, this six-speed automatic transmission has been developed with attention paid to the gear steps and a wider range of gear ratios. By balanced selection of close-ratio gears in a wider range, the change greatly improves the power performance and fuel economy of the vehicle. To further improve fuel economy we have adopted new technologies such as low-viscosity ATF, neutral control, and deceleration control by extending the fuel cut range (reset speed). We have also adopted a flat-shaped torque converter, small solenoids, an aluminum oil pump cover, etc. to realize the lightest six-speed automatic transmission in the world.

Contribution to carbon neutrality is one of the most important challenges for the automotive industry. As CO2 emission has been reduced through electrification such as hybrid electric vehicle (HEV) and plug-in hybrid electric vehicle (PHEV), internal combustion engines (ICEs) equipped in those powertrain systems are still necessary for the foreseeable future, and continuous efforts to improve fuel efficiency are demanded. To improve powertrain thermal efficiency, direct-injection turbocharged gasoline engines have been widely utilized in recent years. Super lean-burn combustion engine has been researched as a next generation of turbocharged gasoline engines. Further utilization of turbochargers is expected. Compared with turbocharged downsized gasoline engines available in the current market, much higher boost pressure must be utilized to realize the super lean-burn engines. As a result, compressor housing temperature will be very high compared with the current market one.

The noise generation mechanism of a direct-acting valve train such as used in sporty and luxury cars was determined for both mechanical and hydraulic tappets through measurements of sound pressure levels and vibrations and the use of computer graphics to observe actual valve and tappet movement. Two phenomena were clarified: chatter at low engine speeds and a mechanical noise at high engine speeds. Further experiments established that the noise of a mechanical tappet can be greatly reduced and its tonal quality improved by optimizing the cam profile and by increasing the acoustic damping ratio of the tappet.

Recently, the smokeless rich diesel combustion had been demonstrated [1]. This can realize smokeless and NOx-less combustion by using a large amount of cooled EGR under a near stoichiometric and even in a rich operating condition. We focus on the effects of reducing diesel combustion temperature on soot reduction.

The newly-developed 2JZ engine series is available in two types; a naturally aspirated 2JZ-GE and a turbo charged 2JZ-GTE. Both have in-Line-6 cylinder arrangement and displacement volume of 2.997 liters and have attained many features expected for the engines of new era by utilizing new technologies, such as DOHC 4 valve, high compression ratio, a highly rigid structural design which is realized by extensive use of the CAE, a serpentine accessory drive belt, and auto tensioners for timing belt and accessory belt systems. These engines are stroke up versions of the 1JZ engines. The 2JZ-GE engine, which has been developed for the SC300, delivers high performance of 169 KW/6000rpm and 284 Nm/4800rpm by adopting a variable induction system, a knock-control system with two sensors, etc. The other type, the 2JZ-GTE engine which has been developed for the Aristo in japan includes a TWO-WAY-TWIN-TURBO’ system equipped with ceramic turbine wheels.

A new hybrid transmission has been developed for all-wheel-drive (AWD) cars, and is used in the new Lexus LS600h and LS600hL for its first application. It has a compact layout consisting of a power-split device, generator, high-output electric motor, and a two-stage speed reduction device. Combined with a 5-liter V-8 engine, it achieves power performance rivaling 6-liter engine vehicles, the fuel efficiency of a medium-class vehicle, and outstanding quietness. This paper describes the structure, performance, and shift control technology of this hybrid transmission.

Efficiency of Driveshafts have not been analyzed in great detail in the past due to their relatively high efficiency. However, it is possible to obtain about a 0.1 percent increase in fuel economy by decreasing driveshaft torque losses by about 20 percent, owing to the combination mode fuel calculation. In order to improve fuel economy it is necessary to increase the efficiency of the constant velocity universal joint (C.V.J.) used for driveshafts. Additionally, propeller shafts with improved heat characteristics are required. It is for these reasons that this project is conducted. In this paper, the motion of two typical joint used for front-engine, front-drive passenger cars is analyzed geometrically and efficiency formulas are derived. One of the joints is a Rzeppa joint, used on the wheel side of the driveshaft and the other is a tripot joint, used on the differential side. These formulas are then verified by experiment.

For the launch of the redesigned Lexus LS, a new 3.5 L V6 twin turbo engine has been developed aiming at unparalleled performance on four axes, “driving pleasure”, “power-performance”, “quietness” and “fuel economy”. To achieve outstanding power-performance and high thermal efficiency, the specifications have been optimized for high speed combustion. The maximum torque of 600 Nm, power of 310 kW (yielding specific power of 90 kW/L), and the maximum thermal efficiency of 37% have been achieved using several new technologies including a high efficiency turbocharger. A prototype vehicle equipped with this engine and Direct-Shift 10AT achieved a 0-60 mph acceleration time of 4.6 sec, with extremely good CAFE combined fuel economy of 23 mpg and power-performance aligned with V8 turbocharged offerings from competing OEM’s.